Stamped Polymer Clay Jewelry

Materials

  • Makin’s Clay No Bake White Polymer Clay, 2 pkgs.
  • Fire Mountain Gems and Beads Tigertail Beading Wire, 26” length
  • Silver findings, two each: flat headpins, earring wires, crimp beads, jump rings; one barrel clasp

Tools

  • Clearsnap ColorBox Premium Dye Ink by Stephanie Barnard: Black, Tangerine, Grape, Blueberry, Banana
  • Earth Safe Finishes Eco Epoxy
  • Makin’s Clay Tool Set
  • Needle-nose pliers, round-nose pliers, crimping pliers
  • Heat tool
  • Rubber stamp of choice
  • Bead board

Basic Supplies

toothpicks, skewers, zip-lock bag, damp paper towel, plastic-foam ball, scissors, sponge, craft stick, recycled jar lid, cutting mat, tapestry needle, ruler

Directions

STEP 1

  • Roll clay into logs measuring 1/2”x2”-3” in length; make 6-10. See Photo 1.

STEP 2

  • Insert skewer through center of each log; remove and let set for an hour. See Photo 2.

STEP 3

  • Roll clay into logs about 1/4”x2”-3” in length; make 6-10. Insert tapestry needle through center of each log; remove and let set for an hour.

STEP 4

  • Apply inks to all logs with sponge, using several colors on each log; heat set with heat tool. See Photo 3.

STEP 5

  • Apply black ink to rubber stamp of choice and roll 1/2” logs on top of inked stamp. Heat set with heat tool. See Photo 4.

STEP 6

  • Cut 1/2” logs into 1/2” pieces; position each bead on toothpick end. Cut 1/4” logs into 1/4” pieces; place each bead on toothpick. See Photo 5.

STEP 7

  • Following manufacturer’s instructions, mix Eco Epoxy in recycled jar lid. Apply epoxy to each clay bead and insert toothpick end of beads into plastic-foam ball to dry. See Photo 6 and Photo 7.

STEP 8

  • For necklace, cut 26” length of beading wire. Insert wire through crimp bead and then barrel clasp on one end; run wire end back through crimp bead. Push crimp bead close to barrel clasp using crimping pliers; squeeze to crimp bead closed. See Photo 8.

STEP 9

  • String 1/4” beads with 1/2” beads, alternating, for 20” length of wire. Use bead board to hold beads. See Photo 9. At end of 20” length, add crimp bead and other end of barrel clasp; thread wire end back through crimp bead. Pull wire tightly and crimp bead; trim excess wire.

STEP 10

  • For earrings, thread 1/4” bead, 1/2” bead, and 1/4” bead onto headpin; bend remainder of wire with fingers to 90º angle. Form loop with round-nose pliers; wrap wire at bottom of loop, and trim excess. See Photo 10. Repeat for other earring. Attach beaded headpins onto earring wires using jump rings.

Tips

  • 1. Keep the clay you are not using in a zip-lock bag with a damp paper towel so it will not dry out (it will last for months kept this way).
  • 2. Mix Eco Epoxy in recycled jar lid so it can be thrown away or recycled when done.
by Ann Butler Designs
Stamped Polymer Clay Jewelry
Stamped Polymer Clay Jewelry Photo 1
Photo 1 Photo 2
Photo 2 Photo 3
Photo 3 Photo 4
Photo 4 Photo 5
Photo 5 Photo 6
Photo 6 Photo 7
Photo 7 Photo 8
Photo 8 Photo 9
Photo 9 Photo 10
Photo 10